diálogos ELE

ASTM A – Designation: A /A M – 98 (Reapproved ) Standard Test Method for Conducti. Purchase your copy of ASTM A/AM – 17 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. This standard is issued under the fixed designation A/AM; the number This test method is under the jurisdiction of ASTM Committee A01 on Steel, 2.

Author: Gall Kazijind
Country: Lithuania
Language: English (Spanish)
Genre: Finance
Published (Last): 24 March 2016
Pages: 338
PDF File Size: 6.77 Mb
ePub File Size: 9.29 Mb
ISBN: 697-5-19316-770-9
Downloads: 81375
Price: Free* [*Free Regsitration Required]
Uploader: Mazull

Historical Version s – view previous versions of standard. Furnace Survey Equipment 5. This standard is subject to revision at any time by the responsible technical committee and must asgm reviewed every? A superscript epsilon e indicates an editorial change since the last revision or reapproval. This method is used to determine the capability of the furnace to meet the permissible temperature variation speci?

Starting time and chart speed shall be marked on the original temperature charts, 8. Heat Treatment in the Working Zone Results of the application of this test method shall be expressed as a variation from a x991 set point. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM x991 the above address or at phonefaxor service astm. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

ASTM International – Standard References for ASTM A / AM – 17

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Attach survey test sensors to, or set them in the load. In each test, determine the temperature a99 pattern at one or more of the test locations.

The rate of conveyance shall be representative of normal operating conditions. For proposed working zones greater than, or equal to, 12 in. Place them at the outer extremities, the center of the proposed working zone, and in areas of suspected variability in the proposed working zone. Details of this procedure shall be as agreed to between purchaser and supplier. The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order as agreed upon by the purchaser and supplier.

  HARFISTA NA WIETRZE PDF

The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other, without combining values in any way. Regardless of heat treat furnace type, or processing cycle, it may be necessary for users to know the temperature uniformity in the furnace and whether the material is processed in a zone within the furnace that is capable of meeting the applicable permissible temperature variation requirements.

Current edition approved Oct. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.

Survey documentation requirements, and the procedure used to subsequently establish the furnace working zone, are de? A major furnace modi? Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Interpretation of Results and Establishment of the Working Zone 9. Calibration to such national standards shall be done at least once every two years.

Survey documentation requirements, and the procedure used to subsequently establish the furnace working zone, are defined in this test method. Examples of these surveying techniques are listed below. AMS Pyrometry3 3.

Originally approved in The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order as agreed upon by the purchaser and supplier. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  LIC JEEVAN SARAL FORM PDF

It provides validation of temperature uniformity by a series of tests rather than a single test. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Regardless of heat treat furnace type, or processing cycle, it may be necessary for users to know the temperature uniformity in the furnace and whether the material is processed in a zone within the furnace that is capable of meeting the applicable permissible temperature variation requirements.

A number in parentheses indicates the year of last reapproval. All other conditions described in 6. This method is used to determine the capability of the furnace to meet the permissible temperature variation specified in the applicable product specification, or as agreed to by the purchaser and supplier of heat treat services.

Within the text, the SI units are shown in brackets. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Combining values from the two systems may result in non-conformance with the standard. Use of representative material to simulate product during survey is permitted.

ASTM A991/A991M – 17

Link to Active This link will always route to the current Active version of the standard. Documentation of Survey Results 8.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. The working zone may be comprised of one or more heating zones in the furnace.