diálogos ELE

CatEye CC-MT [Mity 2] • User guide • Download PDF for free and without registration!. Following pdf manuals are available: cat-eye cc-mt mity 2 User Manual. CatEye product manuals for the entire line of CatEye cycle computers, headlights , safety lights and accessories online support at

Author: Mezisho Mushakar
Country: Mali
Language: English (Spanish)
Genre: Career
Published (Last): 14 August 2008
Pages: 492
PDF File Size: 9.96 Mb
ePub File Size: 10.71 Mb
ISBN: 238-5-94076-391-9
Downloads: 84288
Price: Free* [*Free Regsitration Required]
Uploader: Mikazuru

CatEye CC-MT [Mity 3] User Manual | 4 pages | Original mode | Also for: CC-ED, CC-VL

Display will show default wheel calibration number Press “MODE” right button to enter distance scale selection mode.

Dst 1, 2 Trip Distance 1, 2 0. Odo Total Distance Odometer 0. Pressing the “MODE” button will cycle the computer through the modes: Calibration mith will appear. Usually displayed on the upper display and updated once a second.

Product Support

Power Saving Function When the main unit does not receive a signal, or a button has not been pressed for minutes, the power supply is shut down and the main unit will only display the clock.

Data to be reset: C Vectra owner’s manual Battery: Press “Set” button with a ball point pen. Mx moves up as Main Display. Elapsed time is measured from start to current point, in units of hours, minutes and seconds.

Entering “set” mode jity total reset. All displays illuminate, and then ” K ” symbol flashes. Old versions of manufacturers’ Manaul sites preserved on the Internet Archive may list older models.


When the main unit does not receive a signal, or a button has not been pressed for minutes, the power supply is shut down and the main unit will only display the clock. Input wheel circumference A. Av Average Speed 0.

It links to owner’s manuals for most cyclecomputers. If swallowed by mistake, consult a doctor immediately.

Trouble Shooting No display. In this case, the lower display shows the hour digits of Tm data instead of Spd. If these buttons are further held down for more than 3 seconds, the wheel calibration value moves between “A” and “B” values. How the display changes. With the press of S button, Mx data shifts to the upper display. Periodically check if the screws and secure bands have loosened. Entering “Set” mode to revise wheel size without losing mileage: Press “MODE” right cteye to enter “odometer setting” mode.

Average Pace Arrow Shows whether the current speed is faster or slower than the average speed. Are the marking line of the sensor and the center of magnet aligned?

Press “MODE” right button to adjust next digit. Push the “SET” button. Press all the three buttons simultaneously. C Cordless mankal manual. Best for MTB riding and low speed sensitivity. Press AC button on bottom of unit.

Mity 8 owner’s manual. Mity 2 owner’s manual. Be sure to write down the data before replacing the battery. Please let us know of rebranded models which you have identified. When the average speed is zero, or when in the stop state, no pacer symbol appears. When the main unit or the contact gets wet, dry it off with a cloth; rust will cause functional errors.


When unit is in “stop” state, neither trip mileage nor total mileage is recorded, but speed and maximum speed functions work.

Operating instructions – CatEye CC-MT200 [Mity 2] User Manual

Many bicycle computers are rebranded. Is the wire broken? Rapidly increases the figure. These are reset kity, so you can use Trip Distance 2 to record segments within a trip, etc. Never disassemble the main unit. Replace it with a new one. F Solar II owner’s manual Batteries: To change reading between miles and kilometers, appropriate wheel calibration number must be entered.

Cateye mity2 manual – Bike Forums

Push all three buttons at once “SET” button is recessed on bottom of unit. In TmAv and Dst 1, 2 display.

The hour display will flash and can be changed using the “MODE” button, more quickly if you hold the button down.